Industrial maintenance work
Home / Solutions / Lubricant monitoring

Engineering extension · application-led

From oil signals to planned maintenance.

Extend machine monitoring with selected fluid and lubrication-system sensors. MachBeat can connect validated readings to asset trends, human review and CMMS work orders.

The current MachBeat V1 reference node measures vibration only. Oil properties require application-specific sensors, integration and validation.

Two related monitoring problems

Is the oil healthy - and is it reaching the machine?

Oil chemistry and lubrication delivery need different sensors. A useful installation begins with the failure the plant wants to prevent, not a generic sensor bundle.

01

Lubricant condition

Depending on the oil and application, monitor selected parameters such as temperature-compensated viscosity or density, water saturation and particle cleanliness. Chemical ageing, additive health and wear metals may need laboratory analysis or specialist sensing.

Sensor package selected per fluid
02

Lubrication delivery

Monitor reservoir level, supply pressure, flow, pump cycles, filter differential pressure and temperature where useful. These signals can help surface leaks, blocked lines or filters, pump problems and low supply.

Instrumentation scoped per machine

Failure mechanisms & evidence

What a change may mean - and what to do next.

Each signal is an investigative cue. Limits must be chosen for the actual lubricant, machine, operating state and sensor method; a single reading rarely proves a root cause.

FLOW

Low level, pressure or flow

Could indicate: leakage, empty reservoir, stalled pump, restriction, blocked filter or loss of prime.

Next: inspect the circuit and filter, verify pump delivery, repair the cause and confirm readings after the work.

VISC

Viscosity or density departs

Could indicate: wrong or mixed oil, ageing, shear, dilution or another composition change. Temperature strongly affects interpretation.

Next: compare with the oil-specific reference at a known temperature; check service history and confirm with a suitable sample test.

H₂O

Water saturation rises

Could indicate: condensation, seal or breather ingress, or a leaking cooler/heat exchanger. Water can undermine lubrication and contribute to corrosion.

Next: inspect ingress paths, trend with temperature and confirm absolute water content with an appropriate laboratory method if needed.

ISO

Particle cleanliness worsens

Could indicate: dirt ingress, poor oil handling, filter bypass/failure or generated wear debris. Hydraulic pumps and valves may be sensitive to contamination.

Next: compare with the machine's cleanliness target; inspect filtration and breathers, then trend after corrective action.

Fe

Wear-debris trend increases

Could indicate: active wear in a ferrous component or a contamination event. A basic particle count does not identify the particle or failed component.

Next: correlate with vibration and operating history; take a representative sample and involve a reliability or oil-analysis specialist.

AGE

Ageing or oxidation indicators change

Could indicate: thermal stress, oxidation, contamination or additive depletion; a dielectric reading is an application-specific proxy, not a universal oil-life meter.

Next: review temperature and duty trends; validate the proxy against periodic laboratory results before setting action limits.

Density alone is not an oil-health diagnosis. It needs temperature context and an oil-specific reference.

See the system end to end

Follow the lubricant. Follow the evidence.

An application-led concept: sensors watch the lubrication circuit and selected oil properties; MachBeat brings those readings into asset context and a human-reviewed maintenance workflow.

ILLUSTRATIVE SYSTEM FLOW

Choose a step to see what happens.

SENSORS SCOPED PER APPLICATION
STEP 01 / 04

Start with the real oil circuit.

Map the reservoir, pump, filter, supply/return lines and critical machine. Confirm safe measurement points, oil grade, operating range and what failure the site wants to catch.

FIT FIRSTFluid · duty · connection

Concept illustration only. The current V1 reference device is vibration-only. Fluid sensors, process interfaces, thresholds and integrations require engineering, commissioning and validation for the selected application.

Evidence to action

A maintenance workflow, not another disconnected sensor.

The value is the operating loop: collect a trustworthy signal, review it in machine context, and make the follow-up traceable.

01

Measure

Fluid probe and system sensors report selected parameters with units and status.

02

Contextualise

Trend against the correct oil, machine, temperature and operating state.

03

Review

A person checks the evidence and decides whether to sample or inspect.

04

Close the loop

CMMS work order records owner, action, finding and post-work readings.

What must be engineered

Choose the measurement point before the hardware.

Oil is a process medium, so sensor fit depends on the fluid, circuit and operating envelope. A safe bypass/sample loop may be preferable to inserting a probe directly into a critical line.

A

Fluid & machine fit

Identify oil type/grade, viscosity range, temperature, pressure, flow, contamination and machine criticality. Confirm wetted materials, seals, process connection and warranty constraints.

B

Sensor & interface

Select a proven probe for the desired parameter. Verify output and protocol - for example 4-20 mA, Modbus/RS-485, CAN or IO-Link - then engineer suitable power, isolation and gateway inputs.

C

Baseline & validation

Record the known oil, normal operating states and reference sample. Compare field readings with appropriate lab tests; set thresholds only after the customer reliability team agrees the evidence.

Initial application focus

Start where the signal can lead to a clear action.

Hydraulic power units and circulating-oil gearboxes are practical discovery targets: customers can often identify operating conditions, contamination controls, sampling points and a maintenance response. The first pilot should be selected with the site engineer.

Grease systems, engine oils and specialist turbine/compressor oils need separate fit and validation; this page does not claim one sensor package covers them all.

Technical basis

Built around established measurement practice.

Illustrative sensor families and standards below are research references, not an endorsement or a final bill of materials. Sensor selection remains subject to supplier confirmation and site requirements.

Fluid property and moisture sensors

WIKA VTL-30 documents online viscosity, temperature and density measurement for lubricating oils and fuels. HYDAC Aqua Sensor and ifm LDH illustrate dedicated water-in-oil sensing approaches.

Cleanliness and confirmation

ifm LDP illustrates oil particle monitoring; ISO 4406:2021 defines a solid-particle contamination code for hydraulic fluids. ASTM D445 is a laboratory method for kinematic viscosity - it is not a substitute for validating an online probe.

For deeper failure mapping and pilot design, see the oil-condition monitoring research brief.

Industrial equipment in a factory

Start with the fault the plant wants to prevent.

Bring the machine type, lubricant grade, existing oil results and likely sample points. MachBeat can help scope whether a sensor-led pilot is technically justified.

No guaranteed failure prediction · no universal oil threshold